-- *****************************************************************
-- OLD-CISCO-SYS-MIB.my:  Cisco System MIB file
--
-- July 1994, Jeffrey T. Johnson
--
-- Copyright (c) 1994-1996 by cisco Systems, Inc.
-- All rights reserved.
-- 
-- *****************************************************************
--
-- Prior to 10.2, Cisco's lsystem mib group contained a curious
-- assortment of mib objects.  For 10.2, in order to allow similar
-- objects to be compiled separately with the mib compiler, the
-- lsystem group was separated into an envmon group (lenv), a cpu
-- group (lcpu), a memory group (lmem), and a system group (lsystem).
-- In order to preserve the OBJECT IDENTIFIERS from release 10.1 to
-- 10.2, however, all four groups are still based at { local 1 }.
-- This is fine from the mib compiler point-of-view, but causes
-- problems for some test tools which don't like the fact that
-- lsystem, lenv, lmem, and lcpu all have the same OBJECT IDENTIFIER.
-- In order to work around this problem, this file exists which
-- is a combination of the four 10.2 "system" mibs, with everything
-- falling under the lsystem group (as it did in 10.1).
--
-- This mib should only be used as a replacement for the four separate
-- system mibs (OLD-CISCO-CPU.my, OLD-CISCO-ENVMON-MIB.my,
-- OLD-CISCO-MEMORY-MIB.my, OLD-CISCO-SYSTEM-MIB.my) in test tool
-- environments.  The aforementioned mibs should always be used in
-- code generation

               OLD-CISCO-SYS-MIB DEFINITIONS ::= BEGIN

               IMPORTS
                    IpAddress
                        FROM RFC1155-SMI
                    OBJECT-TYPE
                        FROM RFC-1212
                    DisplayString
                        FROM RFC1213-MIB
                    local
                        FROM CISCO-SMI;
          
               lsystem             OBJECT IDENTIFIER ::= { local 1 }

          -- Local Variable Section

          -- This section describes the local variables within the cisco
          -- product line.  Groups may or may not be present depending
          -- on the software options present in the managed device.


          -- Local System Group

          -- This group is present in all products.

               romId OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "This variable contains a printable octet
                           string which contains the System Bootstrap
                           description and version identification."
                   ::= { lsystem 1 }

               whyReload OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "This variable contains a printable octet
                           string which contains the reason why the
                           system was last restarted."
                   ::= { lsystem 2 }

               hostName OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "This variable represents the name of the
                           host in printable ascii characters."
                   ::= { lsystem 3 }

               domainName OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "This variable is the domain portion of the
                           domain name of the host."
                   ::= { lsystem 4 }

               authAddr OBJECT-TYPE
                   SYNTAX  IpAddress
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "This variable contains the last SNMP
                           authorization failure IP address."
                   ::= { lsystem 5 }

               bootHost OBJECT-TYPE
                   SYNTAX  IpAddress
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the IP address of the host that
                           supplied the currently running software."
                   ::= { lsystem 6 }

               ping OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-write
                   STATUS  obsolete
                   DESCRIPTION
                           "The ping mib object is obsolete as of IOS 10.2
                           It has been superseded by the Cisco Ping MIB"
                   ::= { lsystem 7 }

               freeMem OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  obsolete
                   DESCRIPTION
                           "The freeMem mib object is obsolete as of IOS 11.1
                           It has been replaced with the cisco memory pool mib"
                   ::= { lsystem 8 }

               bufferElFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free buffer
                           elements."
                   ::= { lsystem 9 }

               bufferElMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of buffer
                           elements."
                   ::= { lsystem 10 }

               bufferElHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of buffer element hits."
                   ::= { lsystem 11 }

               bufferElMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of buffer element
                           misses."
                   ::= { lsystem 12 }

               bufferElCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of buffer element
                           creates."
                   ::= { lsystem 13 }

               bufferSmSize OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the size of small buffers."
                   ::= { lsystem 14 }

               bufferSmTotal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the total number of small buffers."
                   ::= { lsystem 15 }

               bufferSmFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free small buffers."
                   ::= { lsystem 16 }

               bufferSmMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of small
                           buffers."
                   ::= { lsystem 17 }

               bufferSmHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of small buffer hits."
                   ::= { lsystem 18 }

               bufferSmMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of small buffer misses."
                   ::= { lsystem 19 }

               bufferSmTrim OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of small buffer trims."
                   ::= { lsystem 20 }

               bufferSmCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of small buffer
                           creates."
                   ::= { lsystem 21 }

               bufferMdSize OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the size of medium buffers."
                   ::= { lsystem 22 }

               bufferMdTotal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the total number of medium
                           buffers."
                   ::= { lsystem 23 }

               bufferMdFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free medium buffers."
                   ::= { lsystem 24 }

               bufferMdMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of medium
                           buffers."
                   ::= { lsystem 25 }

               bufferMdHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of medium buffer hits."
                   ::= { lsystem 26 }

               bufferMdMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of medium buffer
                           misses."
                   ::= { lsystem 27 }

               bufferMdTrim OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of medium buffer trims."
                   ::= { lsystem 28 }

               bufferMdCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of medium buffer
                           creates."
                   ::= { lsystem 29 }

               bufferBgSize OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the size of big buffers."
                   ::= { lsystem 30 }

               bufferBgTotal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the total number of big buffers."
                   ::= { lsystem 31 }

               bufferBgFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free big buffers."
                   ::= { lsystem 32 }

               bufferBgMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of big buffers."
                   ::= { lsystem 33 }

               bufferBgHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of big buffer hits."
                   ::= { lsystem 34 }

               bufferBgMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of big buffer misses."
                   ::= { lsystem 35 }

               bufferBgTrim OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of big buffer trims."
                   ::= { lsystem 36 }

               bufferBgCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of big buffer creates."
                   ::= { lsystem 37 }

               bufferLgSize OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the size of large buffers."
                   ::= { lsystem 38 }

               bufferLgTotal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the total number of large buffers."
                   ::= { lsystem 39 }

               bufferLgFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free large buffers."
                   ::= { lsystem 40 }

               bufferLgMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of large
                           buffers."
                   ::= { lsystem 41 }

               bufferLgHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of large buffer hits."
                   ::= { lsystem 42 }

               bufferLgMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of large buffer misses."
                   ::= { lsystem 43 }

               bufferLgTrim OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of large buffer trims."
                   ::= { lsystem 44 }

               bufferLgCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of large buffer
                           creates."
                   ::= { lsystem 45 }

               bufferFail OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Count of the number of buffer allocation
                           failures."
                   ::= { lsystem 46 }

               bufferNoMem OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Count of the number of buffer create
                           failures due to no free memory."
                   ::= { lsystem 47 }

               netConfigAddr OBJECT-TYPE
                   SYNTAX  IpAddress
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the address of the host that supplied
                           the network-confg file."
                   ::= { lsystem 48 }

               netConfigName OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the name of the network configuration
                           file."
                   ::= { lsystem 49 }

               netConfigSet OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  write-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Cause the loading of a new network-confg
                           file using TFTP."
                   ::= { lsystem 50 }

               hostConfigAddr OBJECT-TYPE
                   SYNTAX  IpAddress
                   ACCESS  read-only
                   STATUS  obsolete
                   DESCRIPTION
                           "Contains the address of the host that
                           provided the host-config file."
                   ::= { lsystem 51 }

               hostConfigName OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  obsolete
                   DESCRIPTION
                           "Contains the name of the last configured
                           host-confg file."
                   ::= { lsystem 52 }

               hostConfigSet OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  write-only
                   STATUS  obsolete
                   DESCRIPTION
                           "Cause the loading of a new host-confg file
                           using TFTP."
                   ::= { lsystem 53 }

               writeMem OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  write-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Write configuration into non-volatile memory
                           / erase config memory if 0."
                   ::= { lsystem 54 }

               writeNet OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  write-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Write configuration to host using TFTP."
                   ::= { lsystem 55 }

               busyPer OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "CPU busy percentage in the last 5 second
                           period. Not the last 5 realtime seconds but
                           the last 5 second period in the scheduler."
                   ::= { lsystem 56 }

               avgBusy1 OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "1 minute exponentially-decayed moving
                           average of the CPU busy percentage."
                   ::= { lsystem 57 }

               avgBusy5 OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "5 minute exponentially-decayed moving
                           average of the CPU busy percentage."
                   ::= { lsystem 58 }

               idleCount OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-write
                   STATUS  mandatory
                   DESCRIPTION
                           "cisco internal variable. not to be used"
                   ::= { lsystem 59 }

               idleWired OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-write
                   STATUS  mandatory
                   DESCRIPTION
                           "cisco internal variable. not to be used"
                   ::= { lsystem 60 }

               ciscoContactInfo OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "cisco's name and address"
                   ::= { lsystem 61 }

               bufferHgSize OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the size of huge buffers."
                   ::= { lsystem 62 }

               bufferHgTotal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the total number of huge buffers."
                   ::= { lsystem 63 }

               bufferHgFree OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of free huge buffers."
                   ::= { lsystem 64 }

               bufferHgMax OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the maximum number of huge
                           buffers."
                   ::= { lsystem 65 }

               bufferHgHit OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of huge buffer hits."
                   ::= { lsystem 66 }

               bufferHgMiss OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of huge buffer misses."
                   ::= { lsystem 67 }

               bufferHgTrim OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of huge buffer trims."
                   ::= { lsystem 68 }

               bufferHgCreate OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Contains the number of huge buffer creates."
                   ::= { lsystem 69 }

               netConfigProto OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the protocol that supplied the
                           network-confg file."
                   ::= { lsystem 70 }

               hostConfigProto OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the protocol that supplied the host-
                           confg file."
                   ::= { lsystem 71 }

               sysConfigAddr OBJECT-TYPE
                   SYNTAX  IpAddress
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the address of the host that supplied
                           the system boot image."
                   ::= { lsystem 72 }

               sysConfigName OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the name of the system boot image."
                   ::= { lsystem 73 }

               sysConfigProto OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Holds the protocol that supplied the system
                           boot image."
                   ::= { lsystem 74 }

               sysClearARP OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  write-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Perform a clearing of the entire ARP cache
                           and invalidation of route caches."
                   ::= { lsystem 75 }

               sysClearInt OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  write-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Clear interface given IfIndex as value."
                   ::= { lsystem 76 }

               envPresent OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is there an environmental monitor card in
                           this box?, 0 - No, 1-AGS card present, wrong
                           firmware, 2-AGS CARD present, firmware ok,
                           3-7000 support"
                   ::= { lsystem 77 }

               envTestPt1Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 1. Typically
                           ambient air or the temperature of air
                           entering the router"
                   ::= { lsystem 78 }

               envTestPt1Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 1. Typically a
                           temperature in centigrade."
                   ::= { lsystem 79 }

               envTestPt2Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 2. Typically
                           airflow or the temperature of air leaving the
                           router"
                   ::= { lsystem 80 }

               envTestPt2Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 2. Typically a
                           temperature in centigrade."
                   ::= { lsystem 81 }

               envTestPt3Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 3. Typically
                           +5 volt"
                   ::= { lsystem 82 }

               envTestPt3Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 3. Typically the
                           value in millivolts of the +5v supply"
                   ::= { lsystem 83 }

               envTestPt4Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 4. Typically
                           +12 volt"
                   ::= { lsystem 84 }

               envTestPt4Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 4. Typically the
                           value in millivolts of the +12v supply"
                   ::= { lsystem 85 }

               envTestPt5Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 5. Typically
                           -12 volt"
                   ::= { lsystem 86 }

               envTestPt5Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 5. Typically the
                           value in millivolts of the -12v supply"
                   ::= { lsystem 87 }

               envTestPt6Descr OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of the test point 6. Typically
                           -5 volt"
                   ::= { lsystem 88 }

               envTestPt6Measure OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Current value of test point 6. Typically the
                           value in millivolts of the -5v supply"
                   ::= { lsystem 89 }

               envTestPt1MarginVal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value at which the router will shutdown.
                           Typically the ambient air temperature that
                           will shut the router down. (e.g. 43)"
                   ::= { lsystem 90 }

               envTestPt2MarginVal OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value at which the router will shutdown.
                           Typically the airflow air temperature that
                           will shut the router down. (e.g. 58)"
                   ::= { lsystem 91 }

               envTestPt3MarginPercent OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "+/- Percentage that will shut the router
                           down, (e.g. 10%) typically +5 volt"
                   ::= { lsystem 92 }

               envTestPt4MarginPercent OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "+/- Percentage that will shut the router
                           down, (e.g. 15%) typically +12 volt"
                   ::= { lsystem 93 }

               envTestPt5MarginPercent OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "+/- Percentage that will shut the router
                           down, (e.g. 15%) typically -12 volt"
                   ::= { lsystem 94 }

               envTestPt6MarginPercent OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "+/- Percentage that will shut the router
                           down, (e.g. 10%) typically -5 volt"
                   ::= { lsystem 95 }

               envTestPt1last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt1 when last shutdown
                           occurred."
                   ::= { lsystem 96 }

               envTestPt2last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt2 when last shutdown
                           occurred."
                   ::= { lsystem 97 }

               envTestPt3last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt3 when last shutdown
                           occurred."
                   ::= { lsystem 98 }

               envTestPt4last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt4 when last shutdown
                           occurred."
                   ::= { lsystem 99 }

               envTestPt5last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt5 when last shutdown
                           occurred."
                   ::= { lsystem 100 }

               envTestPt6last OBJECT-TYPE
                   SYNTAX  INTEGER
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Value of TestPt6 when last shutdown
                           occurred."
                   ::= { lsystem 101 }

               envTestPt1warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 102 }

               envTestPt2warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 103 }

               envTestPt3warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 104 }

               envTestPt4warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 105 }

               envTestPt5warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 106 }

               envTestPt6warn OBJECT-TYPE
                   SYNTAX  INTEGER {
                        warning(1),
                        noWarning(2)
                   }
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Is this test point at a warning level?"
                   ::= { lsystem 107 }

               envFirmVersion OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Description of Environmental Card firmware"
                   ::= { lsystem 108 }

               envTechnicianID OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Technician ID"
                   ::= { lsystem 109 }

               envType OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "The type of environmental card"
                   ::= { lsystem 110 }

               envBurnDate OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "The calibration / burn in date"
                   ::= { lsystem 111 }

               envSerialNumber OBJECT-TYPE
                   SYNTAX  DisplayString
                   ACCESS  read-only
                   STATUS  mandatory
                   DESCRIPTION
                           "Serial Number of environmental monitor card"
                   ::= { lsystem 112 }


         END